It is more faster and easier to pass the Cisco 200-101 exam by using Download Cisco Interconnecting Cisco Networking Devices Part 2 (ICND2) questuins and answers. Immediate access to the Leading 200-101 Exam and find the same core area 200-101 questions with professionally verified answers, then PASS your exam with a high score now.

2021 Sep ccna icnd2 book:

Q21. What are three characteristics of the OSPF routing protocol? (Choose three.) 

A. It converges quickly. 

B. OSPF is a classful routing protocol. 

C. It uses cost to determine the best route. 

D. It uses the DUAL algorithm to determine the best route. 

E. OSPF routers send the complete routing table to all directly attached routers. 

F. OSPF routers discover neighbors before exchanging routing information. 

Answer: ACF 


Q22. Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link? 

A. show frame-relay lmi 

B. show frame-relay map 

C. show frame-relay pvc 

D. show interfaces serial 

Answer: B 


Q23. Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.) 

Router(config)# router ospf 1 

A. All OSPF routers in an area must have the same process ID. 

B. Only one process number can be used on the same router. 

C. Different process identifiers can be used to run multiple OSPF processes 

D. The process number can be any number from 1 to 65,535. 

E. Hello packets are sent to each neighbor to determine the processor identifier. 

Answer: CD 


Q24. Which two of these statements regarding RSTP are correct? (Choose two.) 

A. RSTP cannot operate with PVST+. 

B. RSTP defines new port roles. 

C. RSTP defines no new port states. 

D. RSTP is a proprietary implementation of IEEE 802.1D STP. 

E. RSTP is compatible with the original IEEE 802.1D STP. 

Answer: BE 


Q25. Which command enables IPv6 forwarding on a Cisco router? 

A. ipv6 local 

B. ipv6 host 

C. ipv6 unicast-routing 

D. ipv6 neighbor 

Answer: C 


200-101  free exam

Regenerate vce 200-101:

Q26. Which port state is introduced by Rapid-PVST? 

A. learning 

B. listening 

C. discarding 

D. forwarding 

Answer: C 


Q27. A static map to the S-AMER location is required. Which command should be used to create this map? 




A. frame-relay map ip 172.30.0.3 825 broadcast 

B. frame-relay map ip 172.30.0.3 230 broadcast 

C. frame-relay map ip 172.30.0.3 694 broadcast 

D. frame-relay map ip 172.30.0.3 387 broadcast 

Answer: B 


Q28. A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection? 

A. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# no shut 

B. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation ppp Main(config-if)# no shut 

C. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation frame-relay Main(config-if)# authentication chap Main(config-if)# no shut 

D. Main(config)# interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)# no shut 

Answer: B 


Q29. At which layer of the OSI model does PPP perform? 

A. Layer 2 

B. Layer 3 

C. Layer 4 

D. Layer 5 

Answer: A 


Q30. At which layer of the OSI model is RSTP used to prevent loops? 

A. physical 

B. data link 

C. network 

D. transport 

Answer: B