100% Guarantee of 200-101 free exam materials and bible for Cisco certification for client, Real Success Guaranteed with Updated 200-101 pdf dumps vce Materials. 100% PASS Interconnecting Cisco Networking Devices Part 2 (ICND2) exam Today!

2021 Oct cisco icnd2:

Q31. Refer to the exhibit. 


Which WAN protocol is being used? 

A. ATM 

B. HDLC 

C. Frame Relay 

D. PPP 

Answer: C 


Q32. Refer to the exhibit. 


Hosts in network 192.168.2.0 are unable to reach hosts in network 192.168.3.0. Based on the output from RouterA, what are two possible reasons for the failure? (Choose two.) 

A. The cable that is connected to S0/0 on RouterA is faulty. 

B. Interface S0/0 on RouterB is administratively down. 

C. Interface S0/0 on RouterA is configured with an incorrect subnet mask. 

D. The IP address that is configured on S0/0 of RouterB is not in the correct subnet. 

E. Interface S0/0 on RouterA is not receiving a clock signal from the CSU/DSU. 

F. The encapsulation that is configured on S0/0 of RouterB does not match the encapsulation that is configured on S0/0 of RouterA. 

Answer: EF 


Q33. What is one benefit of PVST+? 

A. PVST+ supports Layer 3 load balancing without loops. 

B. PVST+ reduces the CPU cycles for all the switches in the network. 

C. PVST+ allows the root switch location to be optimized per VLAN. 

D. PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage. 

Answer: C 


Q34. Refer to the exhibit. **Exhibit Missing**

A technician pastes the configurations in the exhibit into the two new routers shown. Otherwise, the routers are configured with their default configurations. A ping from Host1 to Host2 fails, but the technician is able to ping the S0/0 interface of R2 from Host1. The configurations of the hosts have been verified as correct. What is the cause of the problem? 

A. The serial cable on R1 needs to be replaced. 

B. The interfaces on R2 are not configured properly. 

C. R1 has no route to the 192.168.1.128 network. 

D. The IP addressing scheme has overlapping subnetworks. 

E. The ip subnet-zero command must be configured on both routers. 

Answer: C 


Q35. Which two statistics appear in show frame-relay map output? (Choose two.) 

A. the number of BECN packets that are received by the router 

B. the value of the local DLCI 

C. the number of FECN packets that are received by the router 

D. the status of the PVC that is configured on the router 

E. the IP address of the local router 

Answer: BD 


200-101  free exam

Down to date icnd2 test:

Q36. Refer to the exhibit. 


Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.) 

A. SwitchA, Fa0/2, designated 

B. SwitchA, Fa0/1, root 

C. SwitchB, Gi0/2, root 

D. SwitchB, Gi0/1, designated 

E. SwitchC, Fa0/2, root 

F. SwitchD, Gi0/2, root 

Answer: ABF 


Q37. What are three reasons that an organization with multiple branch offices and roaming users might implement a Cisco VPN solution instead of point-to-point WAN links? (Choose three.) 

A. reduced cost 

B. better throughput 

C. broadband incompatibility 

D. increased security 

E. scalability 

F. reduced latency 

Answer: ADE 


Q38. Refer to the exhibit. 


Assume that all of the router interfaces are operational and configured correctly. How will router R2 be affected by the configuration of R1 that is shown in the exhibit? 

A. Router R2 will not form a neighbor relationship with R1. 

B. Router R2 will obtain a full routing table, including a default route, from R1. 

C. R2 will obtain OSPF updates from R1, but will not obtain a default route from R1. 

D. R2 will not have a route for the directly connected serial network, but all other directly connected networks will be present, as well as the two Ethernet networks connected to R1. 

Answer: A 


Q39. To allow or prevent load balancing to network 172.16.3.0/24, which of the following commands could be used in R2? (Choose two.) 



A. R2(config-if)#clock rate 

B. R2(config-if)#bandwidth 

C. R2(config-if)#ip ospf cost 

D. R2(config-if)#ip ospf priority 

E. R2(config-router)#distance ospf 

Answer: BC 


Q40. Which command is used to enable CHAP authentication, with PAP as the fallback method, on a serial interface? 

A. Router(config-if)# ppp authentication chap fallback ppp 

B. Router(config-if)# ppp authentication chap pap 

C. Router(config-if)# authentication ppp chap fallback ppp 

D. Router(config-if)# authentication ppp chap pap 

Answer: B