Cause all that matters here is passing the Cisco 200-105 exam. Cause all that you need is a high score of 200-105 Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) exam. The only one thing you need to do is downloading Testking 200-105 exam study guides now. We will not let you down with our money-back guarantee.

2021 Nov 200-105 real exam

Q71. - (Topic 2) 

A router is running three routing processes: RIP, OSPF, and EIGRP, each configured with default characteristics. Each process learns a route to the same remote network. 

If there are no static routes to the destination and none of the routes were redistributed, which route will be placed in the IP routing table? 

A. the route learned through EIGRP 

B. the route learned through OSPF 

C. the route learned through RIP 

D. the route with the lowest metric 

E. all three routes with the router load balancing 

Answer:

Reference: 

http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080094195.shtml 

Administrative distance is the feature that routers use in order to select the best path. 

Administrative distance defines the reliability of a routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an administrative distance value. Lowest Administrative distance will be chosen first. 


Q72. - (Topic 2) 

Refer to the exhibit. 

When running EIGRP, what is required for RouterA to exchange routing updates with RouterC? 

A. AS numbers must be changed to match on all the routers 

B. Loopback interfaces must be configured so a DR is elected 

C. The no auto-summary command is needed on Router A and Router C 

D. Router B needs to have two network statements, one for each connected network 

Answer: A Explanation: 

Here we required same autonomous system between router A,B,C.Routing updated always exchange between in same EIGRP EIGRP autonomous system.you can configure more than one EIGRP autonomous system on the same router. This is typically done at a redistribution point where two EIGRP autonomous systems are interconnected. Individual router interfaces should only be included within a single EIGRP autonomous system. Cisco does not recommend running multiple EIGRP autonomous systems on the same set of interfaces on the router. If multiple EIGRP autonomous systems are used with multiple points of mutual redistribution, it can cause discrepancies in the EIGRP topology table if correct filtering is not performed at the redistribution points. If possible, Cisco recommends you configure only one EIGRP autonomous system in any single autonomous system. http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080093f07.shtml 


Q73. DRAG DROP - (Topic 2) 

Answer: Explanation: 

poison reverse: A router learns from its neighbor that a route is down and the router sends an update back to the neighbor with an infinite metric to that routeLSA: The packets flooded when a topology change occurs, causing network routers to update their topological databases and recalculate routes split horizon: This prevents sending information about a routeback out the same interface that originally learned about the route holddown timer: For a given period, this causes the router to ignore any updates with poorer metrics to a lost network 

The internetwork infrastructure of company XYZ consists of a single OSPF area as shown in the graphic. There is concern that a lack of router resources is impeding internetwork performance. As part of examining the router resources, the OSPF DRs need to be known. All the router OSPF priorities are at the default and the router IDs are shown with each router. 

Which routers are likely to have been elected as DR? (Choose two.) 

A. Corp-1 

B. Corp-2 

C. Corp-3 

D. Corp-4 

E. Branch-1 

F. Branch-2 

Answer: D,F 

Explanation: There are 2 segments on the topology above which are separated by Corp-3 router. Each segment will have a DR so we have 2 DRs. 

To select which router will become DR they will compare their router-IDs. The router with highest (best) router-ID will become DR. The router-ID is chosen in the order below: 

The highest IP address assigned to a loopback (logical) interface. 

If a loopback interface is not defined, the highest IP address of all active router’s physical interfaces will be chosen. 

In this question, the IP addresses of loopback interfaces are not mentioned so we will consider IP addresses of all active router’s physical interfaces. Router Corp-4 (10.1.40.40) & Branch-2 (10.2.20.20) have highest “active” IP addresses so they will become DRs. 


Replace 200-105 free exam questions:

Q74. - (Topic 2) 

Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used? 

A. hop count 

B. administrative distance 

C. link bandwidth 

D. link delay 

E. link cost 

Answer:

Explanation: 

What Is Administrative Distance? 

http://www.cisco.com/en/US/tech/tk365/technologies_tech_note09186a0080094195.shtml 

Administrative distance is the feature that routers use in order to select the best path. Administrative distance defines the reliability of a routing protocol. Each routing protocol is prioritized in order of most to least reliable (believable) with the help of an administrative distance value. Lowest Administrative distance will be chosen first. 


Q75. DRAG DROP - (Topic 2) 

Answer: 

Explanation: 

+ holddown timer: prevents a router from improperly reinstating a route from a regular routing update 

+ split horizon: prevents information about a route from being sent in the direction from which the route was learned 

+ defining a maximum: prevents invalid updates from looping the internetwork indefinitely 

+ route poisoning: causes a routing protocol to advertise an infinite metric for a failed route 

+ triggered update: decreases convergence time by immediately sending route information in response to a topology change 


Q76. - (Topic 3) 

Which command allows you to verify the encapsulation type (CISCO or IETF) for a Frame Relay link? 

A. show frame-relay lmi 

B. show frame-relay map 

C. show frame-relay pvc 

D. show interfaces serial 

Answer:

Explanation: map will show frame relay encapsulation (cisco or ietf) http://www.cisco.com/en/US/docs/ios/12_2/wan/command/reference/wrffr4.html#wp102934 

"show frame-relay map" will show frame relay encapsulation type (CISCO or IETF)