Want to know Pass4sure 200-120 Exam practice test features? Want to lear more about Cisco CCNA Cisco Certified Network Associate CCNA (803) certification experience? Study Breathing Cisco 200-120 answers to Most recent 200-120 questions at Pass4sure. Gat a success with an absolute guarantee to pass Cisco 200-120 (CCNA Cisco Certified Network Associate CCNA (803)) test on your first attempt.

2021 Dec free ccna 200-120 dumps:

Q31. - (Topic 8) 

Which two statistics appear in show frame-relay map output? (Choose two.) 

A. the number of BECN packets that are received by the router 

B. the value of the local DLCI 

C. the number of FECN packets that are received by the router 

D. the status of the PVC that is configured on the router 

E. the IP address of the local router 

Answer: B,D 


Q32. - (Topic 4) 

A router receives information about network 192.168.10.0/24 from multiple sources. What will the router consider the most reliable information about the path to that network? 

A. a directly connected interface with an address of 192.168.10.254/24 

B. a static route to network 192.168.10.0/24 

C. a RIP update for network 192.168.10.0/24 

D. an OSPF update for network 192.168.0.0/16 

E. a default route with a next hop address of 192.168.10.1 

F. a static route to network 192.168.10.0/24 with a local serial interface configured as the next hop 

Answer:


Q33. - (Topic 5) 

What command instructs the device to timestamp Syslog debug messages in milliseconds? 

A. service timestamps log datetime localtime 

B. service timestamps debug datetime msec 

C. service timestamps debug datetime localtime 

D. service timestamps log datetime msec 

Answer:


Q34. - (Topic 7) 

Refer to the exhibit. 

The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? (Choose two.) 

A. Configure the gateway on Host A as 10.1.1.1. 

B. Configure the gateway on Host B as 10.1.2.254. 

C. Configure the IP address of Host A as 10.1.2.2. 

D. Configure the IP address of Host B as 10.1.2.2. 

E. Configure the masks on both hosts to be 255.255.255.224. 

F. Configure the masks on both hosts to be 255.255.255.240. 

Answer: B,D 


Q35. - (Topic 9) 

What are two requirements for an HSRP group? (Choose two.) 

A. exactly one active router 

B. one or more standby routers 

C. one or more backup virtual routers 

D. exactly one standby active router 

E. exactly one backup virtual router 

Answer: A,B 


Improve ccna 200-120:

Q36. - (Topic 4) 

Refer to the exhibit. 

When running OSPF, what would cause router A not to form an adjacency with router B? 

A. The loopback addresses are on different subnets. 

B. The values of the dead timers on the routers are different. 

C. Route summarization is enabled on both routers. 

D. The process identifier on router A is different than the process identifier on router B. 

Answer:


Q37. - (Topic 6) 

Refer to the exhibit. 

The following commands are executed on interface fa0/1 of 2950Switch. 

2950Switch(config-if)# switchport port-security 

2950Switch(config-if)# switchport port-security mac-address sticky 

2950Switch(config-if)# switchport port-security maximum 1 

The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frame is received by 2950Switch? (Choose two.) 

A. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF. 

B. Only host A will be allowed to transmit frames on fa0/1. 

C. This frame will be discarded when it is received by 2950Switch. 

D. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1. 

E. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1. 

F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1. 

Answer: B,D 


Q38. - (Topic 2) 

Refer to the exhibit. 

The output that is shown is generated at a switch. Which three statements are true? (Choose three.) 

A. All ports will be in a state of discarding, learning, or forwarding. 

B. Thirty VLANs have been configured on this switch. 

C. The bridge priority is lower than the default value for spanning tree. 

D. All interfaces that are shown are on shared media. 

E. All designated ports are in a forwarding state. 

F. This switch must be the root bridge for all VLANs on this switch. 

Answer: A,C,E 


Q39. - (Topic 2) 

Refer to the exhibit. 

How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices? 

A. The ports only need to be connected by a crossover cable. 

B. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode trunk 

C. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode access SwitchX(config-if)# switchport access vlan 1 

D. SwitchX(config)# interface fastethernet 0/1 SwitchX(config-if)# switchport mode trunk SwitchX(config-if)# switchport trunk vlan 1 SwitchX(config-if)# switchport trunk vlan 10 SwitchX(config-if)# switchport trunk vlan 20 

Answer:


Q40. - (Topic 2) 

Refer to the exhibit. 

Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE 802.1Q-compliant trunk to another switch. Based on the output shown, what is the reason the trunk does not form, even though the proper cabling has been attached? 

A. VLANs have not been created yet. 

B. An IP address must be configured for the port. 

C. The port is currently configured for access mode. 

D. The correct encapsulation type has not been configured. 

E. The “no shutdown” command has not been entered for the port. 

Answer: