Act now and download your Cisco 200-125 test today! Do not waste time for the worthless Cisco 200-125 tutorials. Download Improved Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) exam with real questions and answers and begin to learn Cisco 200-125 with a classic professional.

2021 Aug 200-125 exam question

Q231. - (Topic 4) 

Which two statements about the OSPF Router ID are true? (Choose two.) 

A. It identifies the source of a Type 1 LSA. 

B. It should be the same on all routers in an OSPF routing instance. 

C. By default, the lowest IP address on the router becomes the OSPF Router ID. 

D. The router automatically chooses the IP address of a loopback as the OSPF Router ID. 

E. It is created using the MAC Address of the loopback interface. 

Answer: A,D 


Q232. - (Topic 4) 

Refer to the exhibit. 


Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown? 

A. One interface has a problem. 

B. Two interfaces have problems. 

C. The interfaces are functioning correctly. 

D. The operational status of the interfaces cannot be determined from the output shown. 

Answer: C 


Q233. DRAG DROP - (Topic 6) 


Answer: 



Q234. - (Topic 4) 

Which command encrypts all plaintext passwords? 

A. Router# service password-encryption 

B. Router(config)# password-encryption 

C. Router(config)# service password-encryption 

D. Router# password-encryption 

Answer: C 


Q235. - (Topic 8) 

It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following procedures are required to accomplish this task? (Choose three.) 

A. Remove the IP address from the physical interface. 

B. Encapsulate the physical interface with multipoint PPP. 

C. Create the virtual interfaces with the interface command. 

D. Configure each subinterface with its own IP address. 

E. Disable split horizon to prevent routing loops between the subinterface networks. 

F. Configure static Frame Relay map entries for each subinterface network. 

Answer: A,C,D 


200-125  practice test

Down to date 200-125 exam fees:

Q236. - (Topic 3) 

Which command can you use to manually assign a static IPv6 address to a router interface? 

A. ipv6 autoconfig 2001:db8:2222:7272::72/64 

B. ipv6 address 2001:db8:2222:7272::72/64 

C. ipv6 address PREFIX_1 ::1/64 

D. ipv6 autoconfig 

Answer: B 


Q237. - (Topic 4) 

Why do large OSPF networks use a hierarchical design? (Choose three.) 

A. to decrease latency by increasing bandwidth 

B. to reduce routing overhead 

C. to speed up convergence 

D. to confine network instability to single areas of the network 

E. to reduce the complexity of router configuration 

F. to lower costs by replacing routers with distribution layer switches 

Answer: B,C,D 


Q238. - (Topic 7) 

Refer to the exhibit. 


The network shown in the diagram is experiencing connectivity problems. Which of the following will correct the problems? (Choose two.) 

A. Configure the gateway on Host A as 10.1.1.1. 

B. Configure the gateway on Host B as 10.1.2.254. 

C. Configure the IP address of Host A as 10.1.2.2. 

D. Configure the IP address of Host B as 10.1.2.2. 

E. Configure the masks on both hosts to be 255.255.255.224. 

F. Configure the masks on both hosts to be 255.255.255.240. 

Answer: B,D 


Q239. - (Topic 7) 

What Cisco IOS feature can be enabled to pinpoint an application that is causing slow network performance? 

A. SNMP 

B. Netflow 

C. WCCP 

D. IP SLA 

Answer: B 


Q240. - (Topic 2) 

Three switches are connected to one another via trunk ports. Assuming the default switch configuration, which switch is elected as the root bridge for the spanning-tree instance of VLAN 1? 

A. the switch with the highest MAC address 

B. the switch with the lowest MAC address 

C. the switch with the highest IP address 

D. the switch with the lowest IP address 

Answer: B