Exambible presents the Cisco 200-125 in two forms-PDF files and Test powerplant software. Youd better have a test before buying. Then youll find exactly what can be done in reduced and higher proficiency. Choose the suitable Cisco 200-125 practice materials as outlined by personal requires. All the Cisco exam contents involving Pdf files can download regarding free after purchasing. The particular test powerplant will develop a real testing environment for you, which will cause you to be feel free and confident from the Cisco 200-125 actual exam. Get full advantage of our Cisco Cisco studying resources, you will pass the Cisco exam with a higher mark. We provide nearly 100% guarantee to get certified with the assistance involving Exambibles products. in fact, you will get full refund should you fail. Or it is possible to order an additional Cisco Cisco 200-125 exam dumps for free.

2021 Oct 200-125 free question

Q81. - (Topic 8) 

Refer to the exhibit. 

Which statement describes DLCI 17? 

A. DLCI 17 describes the ISDN circuit between R2 and R3. 

B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1. 

C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3. 

D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider. 

Answer: C 

Q82. - (Topic 5) 

Which two statements about static NAT translations are true? (Choose two.) 

A. They allow connections to be initiated from the outside. 

B. They require no inside or outside interface markings because addresses are statically defined. 

C. They are always present in the NAT table. 

D. They can be configured with access lists, to allow two or more connections to be initiated from the outside. 

Answer: A,C 

Q83. - (Topic 6) 

Which two commands correctly verify whether port security has been configured on port FastEthernet 0/12 on a switch? (Choose two.) 

A. SW1#show port-secure interface FastEthernet 0/12 

B. SW1#show switchport port-secure interface FastEthernet 0/12 

C. SW1#show running-config 

D. SW1#show port-security interface FastEthernet 0/12 

E. SW1#show switchport port-security interface FastEthernet 0/12 

Answer: C,D 

Q84. - (Topic 1) 

Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. 

Which of the following are true? (Choose two.) 

A. Router C will use ICMP to inform Host 1 that Host 2 cannot be reached. 

B. Router C will use ICMP to inform Router B that Host 2 cannot be reached. 

C. Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached. 

D. Router C will send a Destination Unreachable message type. 

E. Router C will send a Router Selection message type. 

F. Router C will send a Source Quench message type. 

Answer: A,D 

Q85. - (Topic 7) 


Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links. 

You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices. 

An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office. What is causing the problem? 

A. There is an area ID mismatch. 

B. There is a PPP authentication issue; a password mismatch. 

C. There is an OSPF hello and dead interval mismatch. 

D. There is a missing network command in the OSPF process on R5. 

Answer: C 


Regenerate 200-125 actual exam:

Q86. CORRECT TEXT - (Topic 7) 

A network associate is configuring a router for the weaver company to provide internet access. The ISP has provided the company six public IP addresses of The company has 14 hosts that need to access the internet simultaneously. The hosts in the company LAN have been assigned private space addresses in the range of – 

Answer: The company has 14 hosts that need to access the internet simultaneously but we just have 6 public IP addresses from to 

Therefore we have to use NAT overload (or PAT) 

Double click on the Weaver router to open it 

Router>enable Router#configure terminal 

First you should change the router's name to Weaver 

Router(config)#hostname Weaver 

Create a NAT pool of global addresses to be allocated with their netmask. 

Weaver(config)#ip nat pool mypool netmask 

Create a standard access control list that permits the addresses that are to be translated 

Weaver(config)#access-list 1 permit 

Establish dynamic source translation, specifying the access list that was defined in the prior step 

Weaver(config)#ip nat inside source list 1 pool mypool overload 

This command translates all source addresses that pass access list 1, which means a source address from to, into an address from the pool named mypool (the pool contains addresses from to 

Overload keyword allows to map multiple IP addresses to a single registered IP address (many-to-one) by using different ports 

The question said that appropriate interfaces have been configured for NAT inside and NAT outside statements. 

This is how to configure the NAT inside and NAT outside, just for your understanding: 

Weaver(config)#interface fa0/0 

Weaver(config-if)#ip nat inside 


Weaver(config)#interface s0/0 

Weaver(config-if)#ip nat outside 


Finally, we should save all your work with the following command: 

Weaver#copy running-config startup-config 

Check your configuration by going to "Host for testing" and type: 

C :>ping 

The ping should work well and you will be replied from 

Q87. - (Topic 4) 

What is the default maximum number of equal-cost paths that can be placed into the routing table of a Cisco OSPF router? 

A. 2 

B. 8 

C. 16 

D. unlimited 

Answer: B 

Q88. DRAG DROP - (Topic 1) 


Q89. - (Topic 3) 

Refer to the exhibit. 

A new subnet with 60 hosts has been added to the network. Which subnet address should this network use to provide enough usable addresses while wasting the fewest addresses? 





Answer: C 

Q90. - (Topic 3) 

How many bits are contained in each field of an IPv6 address? 

A. 24 

B. 4 

C. 8 

D. 16 

Answer: D