Act now and download your Cisco 200-125 test today! Do not waste time for the worthless Cisco 200-125 tutorials. Download Down to date Cisco CCNA Cisco Certified Network Associate CCNA (v3.0) exam with real questions and answers and begin to learn Cisco 200-125 with a classic professional.

2021 Oct 200-125 study guide

Q141. - (Topic 3) 

Which subnet mask would be appropriate for a network address range to be subnetted for up to eight LANs, with each LAN containing 5 to 26 hosts? 

A. 0.0.0.240 

B. 255.255.255.252 

C. 255.255.255.0 

D. 255.255.255.224 

E. 255.255.255.240 

Answer: D 


Q142. - (Topic 8) 

Which protocol is an open standard protocol framework that is commonly used in VPNs, to provide secure end-to-end communications? 

A. RSA 

B. L2TP 

C. IPsec 

D. PPTP 

Answer: C 


Q143. - (Topic 2) 

VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan 3 command in interface configuration mode? 

A. The command is rejected. 

B. The port turns amber. 

C. The command is accepted and the respective VLAN is added to vlan.dat. 

D. The command is accepted and you must configure the VLAN manually. 

Answer: C 


Q144. - (Topic 4) 

Refer to the exhibit. 


The speed of all serial links is E1 and the speed of all Ethernet links is 100 Mb/s. A static route will be established on the Manchester router to direct traffic toward the Internet over the most direct path available. What configuration on the Manchester router will establish a route toward the Internet for traffic that originates from workstations on the Manchester LAN? 

A. ip route 0.0.0.0 255.255.255.0 172.16.100.2 

B. ip route 0.0.0.0 0.0.0.0 128.107.1.1 

C. ip route 0.0.0.0 255.255.255.252 128.107.1.1 

D. ip route 0.0.0.0 0.0.0.0 172.16.100.1 

E. ip route 0.0.0.0 0.0.0.0 172.16.100.2 

F. ip route 0.0.0.0 255.255.255.255 172.16.100.2 

Answer: E 


Q145. - (Topic 9) 

What is the correct routing match to reach 172.16.1.5/32? 

A. 172.16.1.0/26 

B. 172.16.1.0/25 

C. 172.16.1.0/24 

D. the default route 

Answer: A 


2passeasy.com

Avant-garde 200-125 practice exam:

Q146. - (Topic 4) 

Refer to the exhibit. 


A network administrator configures a new router and enters the copy startup-config running-config command on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enters the system configuration dialog as shown. What is the cause of the problem? 

A. The network administrator failed to save the configuration. 

B. The configuration register is set to 0x2100. 

C. The boot system flash command is missing from the configuration. 

D. The configuration register is set to 0x2102. 

E. The router is configured with the boot system startup command. 

Answer: A 


Q147. DRAG DROP - (Topic 1) 


Answer: 



Q148. DRAG DROP - (Topic 1) 


Answer: 



Q149. - (Topic 2) 

Refer to the exhibit. 


A network administrator is configuring an EtherChannel between SW1 and SW2. The SW1 configuration is shown. What is the correct configuration for SW2? 

A. interface FastEthernet 0/1 

channel-group 1 mode active 

switchport trunk encapsulation dot1q 

switchport mode trunk 

interface FastEthernet 0/2 

channel-group 1 mode active 

switchport trunk encapsulation dot1q 

switchport mode trunk 

B. interface FastEthernet 0/1 

channel-group 2 mode auto 

switchport trunk encapsulation dot1q 

switchport mode trunk 

interface FastEthernet 0/2 

channel-group 2 mode auto 

switchport trunk encapsulation dot1q 

switchport mode trunk 

C. interface FastEthernet 0/1 

channel-group 1 mode desirable 

switchport trunk encapsulation dot1q 

switchport mode trunk 

interface FastEthernet 0/2 

channel-group 1 mode desirable 

switchport trunk encapsulation dot1q 

switchport mode trunk 

D. interface FastEthernet 0/1 

channel-group 1 mode passive 

switchport trunk encapsulation dot1q 

switchport mode trunk 

interface FastEthernet 0/2 

channel-group 1 mode passive 

switchport trunk encapsulation dot1q 

switchport mode trunk 

Answer: C 


Q150. - (Topic 9) 

What are two requirements for an HSRP group? (Choose two.) 

A. exactly one active router 

B. one or more standby routers 

C. one or more backup virtual routers 

D. exactly one standby active router 

E. exactly one backup virtual router 

Answer: A,B