Want to know Exambible 200-401 Exam practice test features? Want to lear more about Cisco Managing Industrial Networks with Cisco Networking Technologies certification experience? Study Virtual Cisco 200-401 answers to Regenerate 200-401 questions at Exambible. Gat a success with an absolute guarantee to pass Cisco 200-401 (Managing Industrial Networks with Cisco Networking Technologies) test on your first attempt.

2021 Nov byp 401-200:

Q31. DRAG DROP - (Topic 2) 

Answer: 


Q32. - (Topic 2) 

Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.) 

A. designated ports 

B. duplex operating mode 

C. fast mode ports 

D. root bridge 

E. root ports 

F. BDPU priority 

Answer: A,D,E 


Q33. - (Topic 4) 

What are two recommended tools or commands that allow you to troubleshoot connectivity between two devices in different IP networks? (Choose two.) 

A. show interface status 

B. show spanning-tree 

C. ping 

D. show interfaces gigabitEthernet x/y switchport 

E. traceroute 

F. show interface 

Answer: C,E 


Q34. - (Topic 5) 

Which protocol is a secure alternative to Telnet? 

A. SSH 

B. FTP 

C. SMTP 

D. SNMP 

E. HTTP 

Answer:


Q35. - (Topic 5) 

Exhibit: 

Refer to the exhibit. A technician enters the exhibited commands to configure a new router on the plant floor, but receives an error message when attempting to save the configuration. What can the technician do to correct the problem? 

A. Enter the correct command. 

B. Enter the command at the correct prompt. 

C. Upgrade the amount of flash memory in the router. 

D. Erase NVRAM to make room for the configuration file. 

E. Add NVRAM because there is not enough room for the configuration file. 

Answer:


Up to the immediate present 401 biscayne blvd. r-200:

Q36. - (Topic 4) 

With a Cisco IE 2000 switch, what does a port status LED indicate when it is alternating green and amber? 

A. The port is sending or receiving data. 

B. A link is present. 

C. No link is present. 

D. There is a link fault. 

E. The port is not forwarding. 

Answer:


Q37. - (Topic 4) 

With a Cisco IE 2000 switch, what does a port status LED indicate when it is solid green? 

A. The port is sending or receiving data. 

B. A link is present. 

C. No link is present. 

D. There is a link fault. 

E. The port is not forwarding. 

Answer:


Q38. - (Topic 3) 

Which option best describes a mechanical, ingress, climatic, chemical and electromagnetic environment that is classified as M3 I3 C3 E3? 

A. the highest quality 

B. office environment 

C. severe 

D. serviced by multiple cable segments 

Answer:


Q39. - (Topic 2) 

Given a ring topology, which loop prevention mechanism provides the fastest reconvergence time after a link failure? 

A. Rapid Per-VLAN Spanning Tree Protocol 

B. Resilient Ethernet Protocol 

C. Multiple Spanning Tree Protocol 

D. Spanning Tree Protocol 

Answer:


Q40. - (Topic 4) 

Exhibit: 

Refer to the exhibit. The output that is shown is generated at an industrial switch. Which three statements are true? (Choose three.) 

A. All ports will be in a state of discarding, learning, or forwarding. 

B. Thirty VLANs have been configured on this switch. 

C. The bridge priority is lower than the default value for spanning tree. 

D. All interfaces that are shown are on shared media. 

E. All designated ports are in a forwarding state. 

F. This switch must be the root bridge for all VLANs on this switch. 

Answer: A,C,E