Approved of 200-601 test materials and courses for Cisco certification for client, Real Success Guaranteed with Updated 200-601 pdf dumps vce Materials. 100% PASS Managing Industrial Networking for Manufacturing with Cisco Technologies exam Today!

2021 Dec 200-601 torrent

Q41. A cookie cutter machine requires 2 standard controllers and a safety controller. All of these controllers and machine level I/O have been placed on VLAN 104. Both standard controllers must monitor a photocell on this machine. Which IP address is used to transfer this status information? 

A. 10.17.104.16 

B. 192.168.1.16 

C. 239.192.3.16 

D. 239.192.254.16 

Answer:


Q42. Refer to the exhibit. 

A new device, PanelView, has been added to the network. See the table for device details: 

All devices are able to ping their default gateway and all other devices except PanelView. 

PanelView can only ping its default gateway. 

After the administrator has done some investigation they have discovered the following 

information: 

L3SW1# show run interface 

interface Vlan1 no ip address shutdown ! interface Vlan191 ip address 10.10.27.125 255.255.255.192 ip helper-address 165.28.96.96 ip helper-address 165.28.32.235 no ip redirects standby 191 ip 10.10.27.126 standby 191 priority 120 standby 191 preempt delay minimum 90 no ip route-cache ! interface Vlan398 ip vrf forwarding mosaic ip address 10.15.153.203 255.255.255.0 ip helper-address 10.15.154.252 ip helper-address 10.1.0.252 standby 98 ip 10.15.153.202 standby 98 priority 120 standby 98 preempt delay minimum 90 ! interface Vlan399 ip vrf forwarding mosaic ip address 10.15.154.203 255.255.255.0 

ip helper-address 10.1.0.252 

ip helper-address 10.1.1.252 

standby 99 ip 10.15.154.254 

standby 99 priority 120 

standby 99 preempt delay minimum 90 

L3SW1# show ip route connected 10.0.0.0/8 is variably subnetted, 1149 subnets, 17 masks 

C.10.10.27.64/26 is directly connected, Vlan191 

C.10.10.31.254/32 is directly connected, Loopback1 

What is preventing PanelView from pinging the other endpoints in the network? 

A. Routing isn't enabled on L3SW1 for.SVI 398 and.SVI 399 

B. SVI 191 is in a different routing instance than.SVI 398 and SVI 399 

C. Firewall1 is blocking pings from PanelView to the other endpoints 

D. An access list on L3SW1 is blocking pings from PanelView to the other endpoints 

Answer:


Q43. How are I/O timeout and Safety I/O timeout calculated? 

A. An I/O connection will timeout based on the lower of 4x RPI or 100ms. Safety I/O timeout is calculated as 4xRPI. 

B. An I/O connection will timeout based on the lower of 3x RPI or 100ms. Safety I/O timeout is calculated as 3xRPI. 

C. An I/O connection will timeout based on the lower of 4x RPI or 150ms. Safety I/O timeout is calculated as 2xRPI. 

D. An I/O connection will timeout based on the lower of 3x RPI or 150ms. Safety I/O timeout is calculated as 3xRPI. 

Answer:


Replace 200-601 exam cram:

Q44. Refer to the exhibit. 

CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1. You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in: 

L2SW4# show mls interface GigabitEthernet 1/1 statistics 

<output omitted> 

output queues dropped: 

queue:. threshold1. threshold2. threshold3  

queue 0. 0. 0. 0  

queue 1. 309232345. 450. 0. 

queue 2. 300. 10. 0. 

queue 3. 91. 0. 0  

Repeating this command results in the counters incrementing for queue 1 threshold 1. What are two options for reducing the packet loss on this interface while preserving the end-to-end DSCP marking? (Choose two) 

A. Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue 

B. Increase the buffer allocation for input queue 1 

C. Increase the buffer allocation for output queue 1 

D. Alter the service policy to police to a higher CIR 

E. Change the egress queue map on L2SW4 to map this traffic to a less congested queue 

Answer: C,E 


Q45. Which selection is a reason why IGMP snooping should be configured on a switched network? 

A. IGMP snooping populates the snooping table with the results of DHCP requests and can be used by Dynamic ARP Inspection to block IP spoofing attacks at Layer-2. 

B. IGMP snooping verifies the source IP address of every IPv4 packet to ensure that it hasn't been originated from a port different than its return path. 

C. IGMP snooping is used to filter ping requests and results to avoid overflowing the MAC address table of the switch. 

D. IGMP snooping allows a Layer-2 switch to limit the transmission of multicast frames to only the ports that have members of the relevant IGMP group. 

Answer:


Q46. A ProfiNET management system operator is unable to add a ProfiNET Conformance Class B device to a SIMATIC management station. The device is connected to interface 

FastEthernet1/3. Based on the provided CLI output, which statement is correct? 

switch#show profinet lldp Fa1/1.port-003-00000 On Fa1/2.port-004-00000 On Fa1/3.port-005-00000 Off Fa1/4.port-006-00000 Off Fa1/5.port-007-00000 On Fa1/6.port-008-00000 Off Fa1/7.port-009-00000 On Fa1/8.port-010-00000 Off 

A. LLDP has been disabled on this switch 

B. The connected device is not sending LLDP packets with ProfiNET extensions 

C. The port label needs to be changed on interface FastEthernet 1/3 to "port-003-00000" 

D. ProfiNET is disabled on this switch 

Answer: