Exam Code: 210-065 (Practice Exam Latest Test Questions VCE PDF)
Exam Name: Implementing Cisco Video Network Devices v1.0
Certification Provider: Cisco
Free Today! Guaranteed Training- Pass 210-065 Exam.

2021 Mar 210-065 exam question

Q21. A network engineer wants to perform a factory reset on a Cisco TelePresence MX device from the CLI. Which command should be used? 

A. xConfiguration FactoryReset 

B. xCommand FactoryReset 

C. xCommand SystemUnit FactoryReset 

D. xConfiguration SystemUnit FactoryReset 

Answer:


Q22. You have been informed from the field that a new Cisco TelePresence video endpoint has been deployed with an IPv4 address of 172.28.254.45. You need to check for connectivity from the Cisco Unified Communications Manager server. Which command should be entered to check for network connectivity? 

A. utils network traceroute newsystem.domain254.local 

B. utils network ping 172.28.254.45 

C. ping 172.28.254.45 

D. traceroute 172.28.255.255 

E. utils network host cucm.osl147.local 

Answer:


Q23. Which three items should be considered when restoring a backup to a Cisco VCS Expressway? (Choose three.) 

A. A restart is required to complete the system restore process. 

B. If the backup file is encrypted, an encryption password will be needed. 

C. A valid backup configuration file must be accessible. 

D. A function SFTP server is needed for remote restore. 

E. The VCS expressway must be put into maintenance mode during the upgrade. 

F. A flash drive that is connected to the appliance can be used to restore the configuration. 

G. Cisco TMSXE can be used to process and restore backups. 

Answer: A,B,C 


Q24. An engineer wants to know if there is a way to determine the optical zoom of a Cisco TelePresence SX20 remotely. Which two methods will retrieve this information? (Choose two.) 

A. From the CLI, run xstatus. 

B. From the CLI, run xconfig. 

C. From the web GUI, choose Configuration > System Status > Camera. 

D. From the web GUI, choose Configuration> Camera > Status. 

E. From CLI, run xcommand camera. 

Answer: A,C 


Q25. When connecting to a pan-tilt-zoom camera to a C-Series codec, what type of cable must be used for camera control? 

A. an Ethernet crossover cable (RJ45-to-RJ45) 

B. an Ethernet cable (RJ45-to-RJ45) 

C. a serial cable (DB25-to-DB9) 

D. a VISCA cable (DB9-to-RJ45) 

Answer:


Up to the immediate present 210-065 exam:

Q26. Cisco Video Surveillance Video Encoder cards perform which function? 

A. the ability to use existing analog equipment with an IP-enabled video surveillance system 

B. the ability to convert low-resolution video to high-definition video for video surveillance 

C. the ability to stream digital media to digital media in an IP-enabled video recording environment 

D. the ability to encrypt raw video signals to secure video signals 

Answer:


Q27. Which Cisco Video Surveillance product contains the Cisco Video Surveillance Encoding Server? 

A. Video Communications Server 

B. Cisco Video Surveillance Operations Manager 

C. Cisco Video Surveillance Media Server 

D. Cisco Video Surveillance Transcoding and Encoding Server 

E. Cisco Video Surveillance Virtual Matrix 

Answer:


Q28. You have installed a C-Series endpoint in an office where DHCP is not supported. At a minimum, which four network items must be configured for the endpoint to be able to register with H.323 on a Cisco TelePresence Video Communication Server located at the external headquarters location? (Choose four.) 

A. unique IPv4 address 

B. subnet mask 

C. default gateway 

D. Cisco VCS IPv4 address 

E. Active Directory IPv4 address 

F. SMTP server IPv4 address 

Answer: A,B,C,D 


Q29. Refer to the exhibit. 

A network engineer configures a Cisco Unified Communications Manager and VCS integration via a SIP trunk. Endpoint A is able to conduct video calls to Endpoint B. When Endpoint A attempts to share presentation content with Endpoint B, Endpoint B sees the presentation video on the main screen rather than on the presentation display. What is the cause? 

A. The default MTP telephony payload is incorrect. 

B. The SIP trunk is not running on all active Cisco Unified Communications Manager nodes. 

C. MTP is not forced to be required. 

D. BFCP is not enabled. 

E. The MTP preferred codec is incorrect for content presentation. 

Answer:


Q30. What is the main difference between Cisco Jabber and Cisco Jabber Video for TelePresence? 

A. Cisco Jabber registers to the Cisco Unified Communications Manager, whereas Cisco Jabber Video for TelePresence registers to the VCS. 

B. Cisco Jabber Video for TelePresence registers to Cisco Unified Communications Manager, whereas Cisco Jabber registers to the VCS. 

C. Cisco Jabber has no video calling capabilities, whereas Cisco Jabber Video for TelePresence has video capabilities. 

D. Cisco Jabber has no presence capabilities, whereas Cisco Jabber Video for TelePresence has presence capabilities. 

E. There is no difference between Cisco Jabber and Cisco Jabber Video for TelePresence. They should not coexist in the same network. 

Answer: