Q11. A user is currently on a Cisco TelePresence call using a Touch 8 device and would like to change the local screen layout so that the active speaker is in full screen and the other participants are smaller within the picture. Which layout option should the user choose? 

A. Prominent 

B. Overlay 

C. PiP 

D. FullScreen 

Answer:


Q12. Refer to the exhibit. 

Management would like to find out when a particular multipoint control unit feature was enabled and who enabled it. Which menu option is the most appropriate when searching for that information? 

A. Event Display Filter 

B. Audit Log 

C. Event Log 

D. Syslog 

Answer:


Q13. When placing a call from Cisco Jabber Video for TelePresence to the Cisco TelePresence System Codec C40, which FECCs are available? 

A. Only zoom-in and zoom-out are available. 

B. Only left and right are available. 

C. Only up and down are available. 

D. No FECC is available. 

E. Left, right, up, down, zoom-in, and zoom-out are all available. 

Answer:


Q14. Which two of these support an ad-hoc conference call? (Choose two.) 

A. Cisco TelePresence Multiway with Cisco TelePresence Multipoint Control Unit and Cisco TelePresence Video Communications Server 

B. using the Cisco TelePresence Management Suite Scheduler to schedule a conference call to start in 5 minutes 

C. using the Booking tab in the Cisco TelePresence Management Suite to configure a new conference 

D. using the tab Administrative Tools > Configuration > Conference Settings in the Cisco TelePresence Management Suite 

E. pressing the conference button on a Cisco Unified IP Phone 8941 to conference in a third call 

Answer: A,E 


Q15. Threat monitoring in physical access security can be based upon which three of these? (Choose three.) 

A. doors 

B. badges 

C. age 

D. weather 

E. height 

F. fingerprints 

Answer: A,B,F 


Q16. In this item, you will need to use all information presented to you to successfully answer the question. 

Refer to the exhibits. An administrator needs to perform a factory reset on a C-Series endpoint. What are two valid ways to accomplish this task? (Choose two.) 

A. Exhibit A 

B. Exhibit B 

C. Exhibit C 

D. Exhibit D 

E. Exhibit E 

Answer: C,D 


Q17. A technician is trying to troubleshoot real-time call information from the CLI of a VCS. Which command should the technician enter? 

A. xstatus 

B. xconfiguration 

C. xfeedback 

D. xhistory 

E. xcommand 

Answer:


Q18. When scheduling a multipoint conference, which three devices are required for the conference to be scheduled and completed successfully? (Choose three.) 

A. Cisco Unified Communications Manager 

B. multipoint control unit 

C. video conferencing endpoints 

D. Cisco Unity Connection 

E. Cisco Unified IM and Presence 

Answer: A,B,C 


Q19. An engineer needs to configure cascading to support additional video conference attendees. What are three capabilities when cascading? (Choose three.) 

A. Conductor automatically performs cascading. 

B. A maximum of four multipoint control units are supported. 

C. Cascading is supported for the Cisco TelePresence Server in remotely managed mode. 

D. It is possible to manually create a cascaded conference via the Cisco TelePresence MCU Management API. 

E. Cascading is supported for multipoint control units that are registered to Cisco Unified Communications Manager. 

F. All cascaded multipoint control units must be in the same location. 

Answer: A,C,D 


Q20. Which four features are provided by Cisco TelePresence Management Suite? (Choose four.) 

A. Scheduling of video conference calls 

B. Built-in-bridge functionality for multiparty video conferences 

C. SIP-H.323 protocol interworking 

D. Centralized management of conference resources 

E. SMTP email event notification 

F. Endpoint configuration backup and restore 

G. Cisco TelePresence endpoint automated redundancy 

H. Automated resource optimization 

Answer: A,D,E,F