Want to know Pass4sure 210-065 Exam practice test features? Want to lear more about Cisco Implementing Cisco Video Network Devices v1.0 certification experience? Study Breathing Cisco 210-065 answers to Renovate 210-065 questions at Pass4sure. Gat a success with an absolute guarantee to pass Cisco 210-065 (Implementing Cisco Video Network Devices v1.0) test on your first attempt.

Q41. Refer to the exhibit. 

Which tab can be used in order to check the call statistics for the Cisco TelePresence Codec C60? 

A. Diagnostics 

B. Configuration 

C. Call Control 

D. Maintenance 

E. The GUI cannot be used to view call statistics. 

Answer:


Q42. Refer to the exhibit. 

An administrator is attempting to register a Cisco TelePresence endpoint to a Cisco VCS. 

The Cisco VCS uses local authentication and a single username for all endpoints. Where is the first place that the administrator should go to resolve the issue? 

A. VCS > Configuration > Authentication > Devices > Local Database 

B. Endpoint > Configuration > System Configuration > Profile 1 > Authentication 

C. VCS > Configuration > Authentication > Outbound Connection Credentials 

D. Endpoint > Configuration > System Configuration > SIP > Profile 1 > Authentication 1 

E. VCS > Configuration > Registration > Allow List 

F. VCS > Configuration > Registration > Deny List 

Answer:


Q43. Refer to the exhibit. 

A network engineer is attempting to register a Cisco TelePresence endpoint to a Cisco VCS. What is the most likely cause of this failure? 

A. The lab.local SIP domain is not configured in the Cisco VCS allow list for registration. 

B. The Cisco VCS failed to bind to the LDAP server, which is where the lab.local SIP domain is learned. 

C. The lab.local SIP domain does not exist on the Cisco VCS. 

D. The endpoint does not have the proper port assignments configured for SIP signaling. 

E. The endpoint uses the TCP protocol and the Cisco VCS is configured to allow only TLS for SIP registrations. 

Answer:


Q44. A Cisco TelePresence EX Series desktop endpoint failed to register to a Cisco VCS. The SIP status shows "Failed: 403 Forbidden" in the endpoint's web interface. What is the first thing that should be checked in the endpoint configuration settings? 

A. Verify that the correct SIP authentication credentials have been configured. 

B. Ensure that CallSetup Mode is set to Gatekeeper. 

C. Verify that Outbound Connection Credentials are properly configured. 

D. Check to see that SIP Mode is set to On. 

Answer:


Q45. Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view multiple participants at the same time? 

A. enhanced continuous presence 

B. active speaker 

C. continuous presence 

D. room switching 

E. speaker switching 

Answer:


Q46. Refer to the exhibit. 

An employee is reviewing the logs from a Cisco TelePresence System unit due to reports of calls being dropped. Which log entry explains the reason for the call failure? 

A. INFO Packet loss detected: 100% loss - no media stream received in the last 10 seconds 

B. INFO Jitter buffers increased 

C. INFO admin CLI login from 10.160.134.15:51151 

D. INFO Main Video stream packet loss detected on the center codec 

Answer:


Q47. Which three of these are functions of the Cisco TelePresence Management Suite? (Choose three.) 

A. automatic software update and release keys 

B. intelligent call routing engine 

C. provisioning a Cisco TelePresence System endpoint 

D. tracing SIP and H.323 calls 

E. managing phonebooks for endpoints that are registered to the Cisco Unified Cisco Unified Communications Manager 

F. rebooting endpoints that are registered to the Cisco TelePresence Video Communications Server 

Answer: A,B,F 


Q48. Refer to the exhibit. 

You have just finished installing a 65-inch dual profile system in a multipurpose room. After powering up the entire system, only one display is used. Using the information in the exhibit, why is the second display not displaying anything from the system? 

A. The Cisco TelePresence profile systems do not support dual display. 

B. The display is not powered on. 

C. The dual display option key has not been input into the codec. 

D. The codec has the appropriate option keys installed, so either the display is not cabled correctly, the codec is configured incorrectly, or there is no input being sent to the display. 

Answer:


Q49. A Cisco TelePresence System 1300 Series endpoint is in the process of booting and the engineer notices a red "X" on the screen for Step 6 in the boot process. What does this red "X" indicate? 

A. The endpoint failed to load its firmware. 

B. There is an error with compact flash. 

C. The endpoint could not obtain an IP address via DHCP. 

D. The touch panel is malfunctioning. 

Answer:


Q50. On a Cisco C-Series codec, where would a technician go to configure the wallpaper? 

A. Configuration > User Administration 

B. Configuration > Personalization 

C. Configuration > Peripherals 

D. Configuration > System Configuration 

Answer: