Want to know Testking 210-065 Exam practice test features? Want to lear more about Cisco Implementing Cisco Video Network Devices v1.0 certification experience? Study Realistic Cisco 210-065 answers to Refresh 210-065 questions at Testking. Gat a success with an absolute guarantee to pass Cisco 210-065 (Implementing Cisco Video Network Devices v1.0) test on your first attempt.

Q31. An engineer is configuring VIP mode for a Cisco TelePresence Multipoint Switch. What are three characteristics the engineer must keep in mind? (Choose three.) 

A. VIP mode can be configured only when the meeting is not active. 

B. The VIP is displayed on the center screen for three screen systems. 

C. Network multipoint meetings are supported. 

D. VIP mode timers must be configured from the CLI. 

E. Locking is not supported. 

F. Only one VIP can be configured for each meeting. 

Answer: B,D,F 


Q32. Which of these involves combining visual elements from separate sources into a single image? 

A. interlacing 

B. compositing 

C. video conferencing 

D. interleaving 

Answer:


Q33. Which two of these are required in order to complete the password recovery of a Cisco TelePresence System endpoint? (Choose two.) 

A. must have FTP enabled on the endpoint 

B. must have SSH enabled on the endpoint 

C. must have the security question answer for the endpoint 

D. must be in the same room as the main display 

E. must have SFTP enabled on the endpoint 

F. must call Cisco TAC for the security code 

Answer: B,D 


Q34. An immersive video room requires acoustic remediation because there is noticeable reverb present. What type of acoustic paneling does Cisco recommend to provide remediation? 

A. NRC rating greater than 0.75 

B. NRC rating greater than 0.5 

C. NRC rating less than 0.75 

D. NRC rating less than 0.5 

Answer:


Q35. Which codec is most suitable for a video streaming solution? 

A. AAC-LD 

B. G.729 

C. H.264 

D. G.711 

Answer:


Q36. The firmware for the primary codec of a Cisco TelePresence System 3010 is being upgraded. Which codec CLI command could be used to check on the progress of the update? 

A. utils upgrade display 

B. utils system version 

C. show upgrade detail 

D. show system upgrade 

Answer:


Q37. A technician has installed and powered on a Cisco TelePresence MCU 5320 and is connected via the console port. The technician needs to determine the IP settings that were automatically assigned via DHCP. Which command should be entered? 

A. xstatus 

B. show network eth0 

C. status 

D. help static 

Answer:


Q38. Refer to the exhibit. 

Which two of these can cause the phone status error icon that is shown in the exhibit? (Choose two.) 

A. The Cisco Unified Communications Manager IM and Presence Service is not available. 

B. The username and password in Cisco Jabber phone services are misconfigured. 

C. The Cisco Jabber initial audio and video settings need to be set. 

D. There is no DN configured for the Cisco Unified Client Services Framework in Cisco Unified Communications Manager. 

E. The Cisco Jabber does not have the correct phone button template and hence cannot register to the Cisco Unified Communications Manager. 

F. The called user presence status is unknown. 

Answer: B,D 


Q39. A customer has a data and VoIP converged network and would like to add video to this network. Which two key QoS elements should be included in the new network design? (Choose two.) 

A. Configure bandwidth management features to smooth bursty traffic and mitigate end-to-end congestion. 

B. Assign a high priority to transactional traffic to maintain quality of business traffic. 

C. Keep video traffic on the low latency queue and move voice traffic to a lower-priority queue. 

D. Apply bandwidth control features that will guarantee bandwidth for the maximum possible amount of video traffic. 

E. Assign both video and voice traffic to use the highest-priority queue. 

Answer: A,D 


Q40. The user of a Cisco TelePresence MX300 wants to control the far-end camera of any video conference participant. Which control device and function is used to control the far-end camera? 

A. Navigate using the TRC5 Remote Control arrow keys. 

B. Tap on the image of one of the participants using touch control. 

C. Use the Touch Control Conference functions. 

D. Use the TRC5 Remote Control home key. 

Answer: