Proper study guides for Down to date Cisco Implementing Cisco IP Routing certified begins with Cisco ccnp route 300 101 dumps pdf preparation products which designed to deliver the Printable ccnp 300 101 questions by making you pass the cisco 300 101 dump test at your first time. Try the free ccnp routing and switching route 300 101 official cert guide demo right now.

Q61. A network engineer initiates the ip sla responder tcp-connect command in order to gather statistics for performance gauging. Which type of statistics does the engineer see? 

A. connectionless-oriented 

B. service-oriented 

C. connection-oriented 

D. application-oriented 

Answer:

Explanation: 

Configuration Examples for IP SLAs TCP Connect Operations The following example shows

how to configure a TCP Connection-oriented operation from Device B to the Telnet port (TCP port 23) of IP

Host 1 (IP address 10.0.0.1), as shown in the "TCP Connect Operation" figure in the "Information About

the IP SLAs TCP Connect Operation" section. The operation is scheduled to start immediately. In this

example, the control protocol is disabled on the source (Device B). IP SLAs uses the control protocol to

notify the IP SLAs responder to enable the target port temporarily. This action allows the responder to reply

to the TCP Connect operation. In this example, because the target is not a Cisco device and a well- known

TCP port is used, there is no need to send the control message. Device A (target device) Configuration

configure terminal ip sla responder tcp-connect ipaddress 10.0.0.1 port 23 

Reference: http://

www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15- mt-book/ sla_tcp_conn.html


Q62. A network engineer has set up VRF-Lite on two routers where all the interfaces are in the same VRF. At a later time, a new loopback is added to Router 1, but it cannot ping any of the existing interfaces. Which two configurations enable the local or remote router to ping the loopback from any existing interface? (Choose two.) 

A. adding a static route for the VRF that points to the global route table 

B. adding the loopback to the VRF 

C. adding dynamic routing between the two routers and advertising the loopback 

D. adding the IP address of the loopback to the export route targets for the VRF 

E. adding a static route for the VRF that points to the loopback interface 

F. adding all interfaces to the global and VRF routing tables 

Answer: A,B 

Explanation: 


Q63. To configure SNMPv3 implementation, a network engineer is using the AuthNoPriv security level. What effect does this action have on the SNMP messages? 

A. They become unauthenticated and unencrypted. 

B. They become authenticated and unencrypted. 

C. They become authenticated and encrypted. 

D. They become unauthenticated and encrypted. 

Answer:

Explanation: 


Q64. How does an IOS router process a packet that should be switched by Cisco Express Forwarding without an FIB entry? 

A. by forwarding the packet 

B. by dropping the packet 

C. by creating a new FIB entry for the packet 

D. by looking in the routing table for an alternate FIB entry 

Answer:

Explanation: 


Q65. Refer to the exhibit. Which statement about the configuration is true? 

A. 20 packets are being sent every 30 seconds. 

B. The monitor starts at 12:05:00 a.m. 

C. Jitter is being tested with TCP packets to port 65051. 

D. The packets that are being sent use DSCP EF. 

Answer:

Explanation: 


Q66. Which three items can you track when you use two time stamps with IP SLAs? (Choose three.) 

A. delay 

B. jitter 

C. packet loss 

D. load 

E. throughput 

F. path 

Answer: A,B,C