We update the particular Cisco 300-115 training materials as quickly as youll find some changes in the Cisco Cisco real exam. Our consumers wont experience any inconvenience or difficulty in planning for the Cisco 300-115 exam. You will get the most recent Cisco Cisco 300-115 exam practice materials from Pass4sure. We will inform of anyone when we upgrade the particular Cisco 300-115 exam dumps through email.

2021 Apr 300-115 practice question

Q41. After UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?

A. Normal UDLD operations that prevent traffic loops.

B. UDLD port is configured in aggressive mode.

C. UDLD is enabled globally.

D. UDLD timers are inconsistent.

Answer: B


Q42. A network engineer deployed a switch that operates the LAN base feature set and decides to use the SDM VLAN template. The SDM template is causing the CPU of the switch to

spike during peak working hours. What is the root cause of this issue?

A. The VLAN receives additional frames from neighboring switches.

B. The SDM VLAN template causes the MAC address-table to overflow.

C. The VLAN template disables routing in hardware.

D. The switch needs to be rebooted before the SDM template takes effect.

Answer: C


Q43. When you configure a private VLAN, which type of port must you configure the gateway router port as?

A. promiscuous port

B. isolated port

C. community port

D. access port

Answer: A


Q44. The network manager has requested that several new VLANs (VLAN 10, 20, and 30) are allowed to traverse the switch trunk interface. After the command switchport trunk allowed vlan 10,20,30 is issued, all other existing VLANs no longer pass traffic over the trunk. What is the root cause of the problem?

A. The command effectively removed all other working VLANs and replaced them with the new VLANs.

B. VTP pruning removed all unused VLANs.

C. ISL was unable to encapsulate more than the already permitted VLANs across the trunk.

D. Allowing additional VLANs across the trunk introduced a loop in the network.

Answer: A


Q45. A network is running VTPv2. After verifying all VTP settings, the network engineer notices that the new switch is not receiving the list of VLANs from the server. Which action resolves this problem?

A. Reload the new switch.

B. Restart the VTP process on the new switch.

C. Reload the VTP server.

D. Verify connected trunk ports.

Answer: D


Avant-garde 300-115 exam fees:

Q46. Which technique allows specific VLANs to be strictly permitted by the administrator?

A. VTP pruning

B. transparent bridging

C. trunk allowed VLANs

D. VLAN access-list

E. L2P tunneling

Answer: C


Q47. If a network engineer applies the command mac-address-table notification mac-move on a Cisco switch port, when is a syslog message generated?

A. A MAC address or host moves between different switch ports.

B. A new MAC address is added to the content-addressable memory.

C. A new MAC address is removed from the content-addressable memory.

D. More than 64 MAC addresses are added to the content-addressable memory.

Answer: A


Q48. Which command configures an HSRP group to become a slave of another HSRP group?

A. standby slave

B. standby group track

C. standby follow

D. standby group backup

Answer: C


Q49. A switch is added into the production network to increase port capacity. A network engineer is configuring the switch for DHCP snooping and IP Source Guard, but is unable to configure ip verify source under several of the interfaces. Which option is the cause of the problem?

A. The local DHCP server is disabled prior to enabling IP Source Guard.

B. The interfaces are configured as Layer 3 using the no switchport command.

C. No VLANs exist on the switch and/or the switch is configured in VTP transparent mode.

D. The switch is configured for sdm prefer routing as the switched database management template.

E. The configured SVIs on the switch have been removed for the associated interfaces.

Answer: B


Q50. Which four LACP components are used to determine which hot-standby links become active after an interface failure within an EtherChannel bundle? (Choose four.)

A. LACP system priority

B. LACP port priority

C. interface MAC address

D. system ID

E. port number

F. hot-standby link identification number

G. interface bandwidth

Answer: ABDE