Master the ccnp 300 115 Implementing Cisco IP Switched Networks content and be ready for exam day success quickly with this Actualtests ccnp routing and switching switch 300 115 official cert guide exam question. We guarantee it!We make it a reality and give you real ccnp switch 300 115 labs questions in our Cisco cisco 300 115 braindumps.Latest 100% VALID Cisco ccnp 300 115 Exam Questions Dumps at below page. You can use our Cisco 300 115 dumps braindumps and pass your exam.

Q61. after configuring new data VLANs 1020 through 1030 on the VTP server, a network engineer notices that none of the VTP clients are receiving the updates. What is the problem?

A. The VTP server must be reloaded.

B. The VTP version number must be set to version 3.

C. After each update to the VTP server, it takes up to 4 hours propagate.

D. VTP must be stopped and restarted on the server.

E. Another switch in the domain has a higher revision number than the server.

Answer: B


Q62. after UDLD is implemented, a Network Administrator noticed that one port stops receiving UDLD packets. This port continues to reestablish until after eight failed retries. The port then transitions into the errdisable state. Which option describes what causes the port to go into the errdisable state?

A. Normal UDLD operations that prevent traffic loops.

B. UDLD port is configured in aggressive mode.

C. UDLD is enabled globally.

D. UDLD timers are inconsistent.

Answer: B


Q63. Which technique automatically limits VLAN traffic to only the switches that require it?

A. access lists

B. DTP in nonegotiate

C. VTP pruning

D. PBR

Answer: C


Q64. What is the maximum number of switches that can be stacked using Cisco StackWise?

A. 4

B. 5

C. 8

D. 9

E. 10

F. 13

Answer: D


Q65. Refer to the exhibit.

A network engineer wants to analyze all incoming and outgoing packets for an interface that is connected to an access switch. Which three items must be configured to mirror traffic to a packet sniffer that is connected to the distribution switch? (Choose three.)

A. A monitor session on the distribution switch with a physical interface as the source and the remote SPAN VLAN as the destination

B. A remote SPAN VLAN on the distribution and access layer switch

C. A monitor session on the access switch with a physical interface source and the remote SPAN VLAN as the destination

D. A monitor session on the distribution switch with a remote SPAN VLAN as the source and physical interface as the destination

E. A monitor session on the access switch with a remote SPAN VLAN source and the physical interface as the destination

F. A monitor session on the distribution switch with a physical interface as the source and a physical interface as the destination

Answer: BCD


Q66. Refer to the exhibit.

Switch A, B, and C are trunked together and have been properly configured for VTP. Switch C receives VLAN information from the VTP server Switch A, but Switch B does not receive any VLAN information. What is the most probable cause of this behavior?

A. Switch B is configured in transparent mode.

B. Switch B is configured with an access port to Switch A, while Switch C is configured with a trunk port to Switch B.

C. The VTP revision number of the Switch B is higher than that of Switch A.

D. The trunk between Switch A and Switch B is misconfigured.

Answer: A


Q67. Which feature describes MAC addresses that are dynamically learned or manually configured, stored in the address table, and added to the running configuration?

A. sticky

B. dynamic

C. static

D. secure

Answer: A


Q68. A network engineer is installing a switch for temporary workers to connect to. The engineer does not want this switch participating in Spanning Tree with the rest of the network; however, end user connectivity is still required. Which spanning-tree feature accomplishes this?

A. BPDUblock

B. BPDUfilter

C. BPDUignore

D. BPDUguard

E. BPDUdisable

Answer: B


Q69. While troubleshooting a network outage, a network engineer discovered an unusually high level of broadcast traffic coming from one of the switch interfaces. Which option decreases consumption of bandwidth used by broadcast traffic?

A. storm control

B. SDM routing

C. Cisco IOS parser

D. integrated routing and bridging

E. Dynamic ARP Inspection

Answer: A


Q70. Refer to the exhibit.

Why would the switch be considered as a root bridge?

A. The bridge priority is 1 and all ports are forwarding.

B. The switch priority for VLAN 1 and the macro specifies "This Bridge is the root".

C. The bridge priority is 128.19 and all ports are forwarding.

D. The switch priority value is zero, it has the lowest priority value for VLAN 1.

Answer: D