Cause all that matters here is passing the Cisco 300-365 exam. Cause all that you need is a high score of 300-365 Deploying Cisco Wireless Enterprise Networks exam. The only one thing you need to do is downloading Pass4sure 300-365 exam study guides now. We will not let you down with our money-back guarantee.
2021 Apr 300-365 practice exam
Q21. Which two options are limitations of using an AP as a workgroup bridge? (Choose two.)
A. Only factory-configured MAPs can support WGB mode.
B. MAPs that are configured in WGB mode do not answer S36 radio measurement requests.
C. A limited subset of Layer 2 security types are supported for wireless clients of a WGB.
D. There is a limit of 20 wired client devices.
E. Multiple VLANs are not supported for wireless clients.
Q22. A downstream packet containing a DSCP value arrives at the WLC Ethernet interface from the wired source network. The WLC is configured for QoS WLAN 802.1p mapping. How does the WLC treat the CAPWAP QoS marking when leaving the controller interface for the respective AP and final wireless client destination?
A. No outer CAPWAP or inner QoS tagging is applied.
B. No outer CAPWAP QoS tag is applied, but the original DSCP is maintained inside CAPWAP.
C. The outer CAPWAP CoS is marked and capped while the inner DSCP maintains the original marking.
D. The outer CAPWAP DHCP is marked and capped without any inner DSCP value.
Q23. An engineer would like to capture NetFlowdata on PI. Which resource is required to allow this?
A. Cisco MSE as NetFlow exporter
B. Prime Infrastructure 1.0 or later
C. Cisco NAC as NetFlow exporter
D. Cisco ISE as NetFlow exporter
Q24. A customer called into the support center with a problem ticket that involves wireless clients having to reauthenticate when they are walking around their office. After further investigation, it was discovered that the customer has two controllers in an N+1 deployment. Which action must the engineer take to troubleshoot the issue?
A. Verify that the wireless controllers are in the same mobility group and that the access points are all on the primary controller.
B. Under the SSID, make sure that 802.1 Iris configured and running for the clients.
C. Make sure that the SSID has the authentication set to 802.1x with Cisco Centralized Key Management so the data clients can roam seamlessly.
D. Verify the access points are spread out between the primary and secondary controller and that the controllers are in the same mobility group.
There is a problem with the East-WLC-2504A. When configuration changes are made to the Employees-East-Wing AP Group that covers the East-Wing, none of the APs receive the updates. Referto the exhibits to determine where the problems are.
What needs to be changed in the configuration of the East-WLC-2504A controller to restore functionality to the Employees-East-Wing AP Group? (Choose four.)
A. Change the AP in the Employees-East-Wing AP Group.
B. Change the IP Address in the east-wing interface.
C. Change the VLAN Identifier in the east-wing interface.
D. Enable Dynamic AP Management in the east-wing interface.
E. Change the Port Number to 2 in the east-wing interface.
F. Add the Primary Controller and IP address to the 3700-East-Wing AP.
G. Change the SSID in the Employees-East-Wing AP Group.
H. Change the Interface/Interface Group In the Employees-East-Wing AP Group.
Improved 300-365 actual test:
Q26. An engineer wants to configure Call Admission Control and ensure that AC is based on the capacity of the AP and considering the possible impact of other APs in the area. Which two configuration options are required? (Choose two.)
B. Admission Control
C. Load-Based AC
D. Add Traffic Stream
E. Reserved Roaming Bandwidth
F. Expedited Bandwidth
Q27. A customer is implementing a massively scaled guest wireless network to support approximately 32,000 clients. For ease of administration, they have required implementing multiple interfaces defined on the WLC and mapped to a single interface group. Which configuration meets this need?
A. 264 interfaces of/25 sized networks
B. 132 interfaces of/24 sized networks
C. 66 interfaces of/23 sized networks
D. 33 interfaces of /22 sized networks
Q28. A wireless engineer wants to enable optimized roaming for their 5GHz wireless network with these settings: -72dBm RSSI value, 25% coverage exception level percentage, and a minimum of 50 packets received.
Which two commands achieve these settings? (Choose two.)
A. config advanced 802.11a coverage data fail-percentage 25
B. config advanced 802.11b optimized-roaming enable
C. config advanced 802.11b coverage data rssi-threshold -72
D. config advanced 802.11a optimized-roaming enable
E. config advanced 802.11a coverage data rssi-threshold -72
Q29. A network engineer is viewing the QBSS information in a packet sniff. Which two QBSS characteristics are crucial for successful troubleshooting? (Choose two.)
A. When only WMM is enabled, information element number 1 QBSS Load information element is sent out in the beacons and probe responses.
B. When only WMM is enabled, information element number 3 QBSS Load information element is sent out in the beacons and probe responses.
C. When the client CAC limit is supported, information element number 2 is sent out in the beacons and probe responses on the bg radios.
D. When the client CAC limit is supported, information element number 1 is sent out in the beacons and probe responses on the bg radios.
E. When only WMM is enabled, information element number 2 QBSS Load information element is sent out in the beacons and probe responses.
Q30. Refer to Exhibit.
A wireless client is connecting to FlexAPI which is currently working standalone mode. The AAA authentication process is returning the following AVPs:
Tunnel-Private-Group-ld(81): 15 Tunnel-Medium-Type(65):IEEE-802(6) Tunnel-Type(64): VLAN(13)
Which three behaviors will the client experience? (Choose three.)
A. While the AP is in standalone mode, the client will be placed in VLAN 15.
B. While the AP is in standalone mode, the client will be placed in VLAN 10.
C. When the AP transitions to connected mode, the client will be de-authenticated.
D. While the AP is in standalone mode, the client will be placed in VLAN 13.
E. When the AP is in connected mode, the client will be placed in VLAN 13.
F. When the AP transitions to connected mode the client will remain associated.
G. When the AP is in connected mode, the client will be placed in VLAN 15.
H. When the AP is in connected mode, the client will be placed in VLAN 10.