Refined of 350-080 free practice test materials and cram for Cisco certification for client, Real Success Guaranteed with Updated 350-080 pdf dumps vce Materials. 100% PASS CCIE Data Center Written Exam exam Today!

2021 Nov 350-080 examcollection:

Q291. A load balancer can be defined as a network device that makes forwarding decisions that are based on parameters in Layers 4 to 7 of the OSI model. Which three parameters are involved in forwarding decisions? (Choose three.)

A. TCP Destination Port

B. DNS Record

C. HTTP Session Cookie

D. SNMP GET

E. String recognized in the connection data

F. Uniform Resource Locater

Answer: A,C,E


Q292. In a FabricPath topology, each device is identified by a switch ID, and all Layer 2 forwarding tables are built based on the reachability of the switch ID. Which protocol is used to assign the switch ID?

A. No protocol is used. The switch ID is always assigned manually.

B. The Dynamic Resource Allocation Protocol is used to assign the switch ID.

C. The Switch ID Assignment Protocol is used to assign the switch ID.

D. The switch ID is assigned based on the system ID of the device.

Answer: B


Q293. Which three statements about FabricPath are true? (Choose three.)

A. Only FabricPath VLANs can cross a FabricPath domain.

B. A vPC+ peer link can be formed out of F1 or F2 ports only.

C. With FabricPath, vPC must be changed to vPC+.

D. F1 ports must be placed into a separate VDCs.

E. A vPC+ peer link can be formed out of F2 ports only.

Answer: A,B,C


Q294. In a Cisco Nexus 7000 platform configured with GLBP, which GLBP timer can be tuned to prevent unnecessary GLBP state changes during a switchover or ISSU?

A. GLBP redirect timer

B. GLBP forwarder pre-empt delay minimum timer

C. GLBP hold timer

D. GLBP pre-empt delay minimum timer

E. GLBP extended hold timer

F. GLBP nonstop forwarding timer

Answer: E


Regenerate actual test 350-080:

Q295. Nexus# conf t

Enter configuration commands, one per line. End with CNTL/Z.

Nexus(config)# interface Loopback10

% Permission denied

Nexus(config)# ?

no Negate a command or set its defaults

username Configure user information.

End Go to exec mode

exit Exit from command interpreter

What is the reason why this user is not able to enter configuration commands?

A. The user did not enter enable prior to going into configuration mode.

B. The software license installed on Nexus is Layer 2 only, which does not allow the creation of Layer 3 interfaces.

C. The user RBAC role is set to network-operator.

D. The user failed authentication and user access defaulted to read-only mode.

E. The AAA server is currently not responding.

Answer: C


Q296. Which of the following is an advanced networking function performed by VEM?

A. QOS.

B. Snooping.

C. VSAN creation.

D. VLAN pruning.

Answer: A


Q297. Which four statements about SNMP implementation on the Cisco Nexus 7000 Series switch are true? (Choose four.)

A. Cisco NX-OS supports one instance of the SNMP per virtual device context.

B. By default, Cisco NX-OS uses the default VDC for SNMP.

C. SNMP supports multiple MIB module instances and maps them to logical network entities.

D. SNMP is VRF aware. You can configure SNMP to use a particular VRF to reach the SNMP notification host receiver.

E. Only SNMP version 3 is supported on NX-OS.

F. Cisco NX-OS supports one instance of the SNMP per switch.

G. Each VDC can have multiple SNMP sessions configured in it.

Answer: A,B,C,D


Q298. RAG DROP

Answer: